- #Mastercam x5 tutorial pdf how to
- #Mastercam x5 tutorial pdf manual
- #Mastercam x5 tutorial pdf software
- #Mastercam x5 tutorial pdf windows
#Mastercam x5 tutorial pdf how to
Make sure that in the Status bar the 3D mode is enabled.ĬREATE THE RECTANGLEIn this step you will learn how to create a rectangle knowing the width, the height and the anchor position.Ģ.1 Create the 9.0" by 6.5" rectangleCreate Rectangle and the Height and disable if needed, Anchor to center and
Repeat this command to make it visible again. From the keyboard, press Alt + O keys simultaneously to hide it. The Operations Manager to the left of the screen can be hidden to gain more space in the graphic area for design. See Getting started page A-6 for further information. It will show you where the part origin is. See Getting started page A-4 for details. SETTING UP THE GRAPHIC USER INTERFACEBefore starting the geometry creation we should customize the toolbars to see the toolbars required to create the geometry and machine a 3D part. This tutorial takes approximately one hour and half to complete. Running the Verify to simulate the tool cutting from the solid model. Running the Backplot to see the path the tool takes to cut the part. The Student will simulate the toolpaths using Mastercam's Verify and Backplot by: Defining a 3-dimensional rectangular block the size of the work piece. Surface Finish Leftover to clean out the part. Surface High Speed - Hybrid to finish the part. Surface Restmill to clean areas that the previous tool can not. The Student will create surface toolpaths consisting of: Surface High Speed - Area Roughing to rough out the part. Creating the wireframe for the draft surfaces. Creating the swept surface Creating the 2D wireframe for the flat surfaces. Creating the draft surfaces at 3 degree angle Creating 2D wireframe for the swept surface. TUTORIAL #4Objectives:The Student will design a 3-dimensional drawing by: Creating the 2D wireframe for the revolved surface. A-1 TutorialsTutorial #1 Tutorial #2 Tutorial #3 Tutorial #4 Tutorial #5 Tutorial #6 Tutorial #7. Mill Level 3 Training Tutorial ContentsGetting Started.
#Mastercam x5 tutorial pdf windows
Windows, Windows XP, Windows Vista and Windows NT are registered trademarks of Microsoft Corporation. Microsoft, the Microsoft logo, MS, and MS-DOS are registered trademarks of Microsoft Corporation NSee is a registered trademark of Microcompatibles, Inc. Trademarks Mastercam is a registered trademark of CNC Software, Inc. This document may not, in whole or part, be copied, photographed, reproduced, translated or reduced to any electronic medium or machine readable form without prior consent, in writing, from In-House Solutions Inc.
#Mastercam x5 tutorial pdf manual
Copyrights This manual is protected under International copyright laws. Some jurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you.
has been advised of the possibility of such damages. be liable for direct, indirect, or consequential damages resulting from any defect in the manual, even if In-House Solutions Inc. Should the manual prove defective following its purchase, the buyer (and not In-House Solutions Inc., its distributer, or its retailer) assumes the entire cost of all necessary servicing, repair, of correction and any incidental or consequential damages. manual is sold or licensed "as is." The entire risk as to its quality and performance is with the buyer.
#Mastercam x5 tutorial pdf software
makes no warranties, either express or implied, with respect to this manual or with respect to the software described in this manual, its quality, performance, merchantability, or fitness for any praticular purpose. Disclaimer Of All Warranties And Liability In-House Solutions Inc. reserves the right to make improvements to this manual at any time and without notice. All rights reserved Software: Mastercam X5 Author: Mariana Lendel ISBN: 978-1-92 Revision Date: OctoNotice In-House Solutions Inc. Mastercam X5 Mill Level 3 Training Tutorial Training Tutorial Copyright: 1998 -2010 In-House Solutions Inc.
To order more books: Call 1-80 or Visit or Contact your Mastercam dealer
0 kommentar(er)
